Author Archive

Customized Sax Case

Sometimes the case you have is not optimal for the sax that needs to fit in it: the case could be too generic, it could be old and in need of repair. It could be a low-A bari case that your Bb bari is swimming around in. The example I am using is creating a snug home for a C-melody sax out of a tenor sax case.

To create my custom-fit case, I bought some new lining fabric (I found some cool leopard-print velvet on-line) and an aerosol can of expandable insulation foam from the hardware store. I draped the fabric inside the case with lots of spare fabric to fit into the folds of the case. Then I uncovered one side of the case and sprayed about a 1″ layer of foam all over the inner well where the sax lies. I covered the foam back up with the fabric, then uncovered the other side and repeated the process, filling the well about 1″ deep. This used up the can and I covered the wet foam with the fabric.

Then, with a deep breath, I put the sax into the case, closed it and wrapped it with wire to keep it closed.

24 hours later I opened it: the foam had expanded enough to conform to the shape of the sax, but not so much I couldn’t get the sax out. Whew!

I trimmed the edge of the cloth to about 1/4″ inside the case zipper, then glued down the edges to the old liner fabric with transparent glue. There are a couple of pockets inside the case for the neck and mouthpiece, I cut and glued the fabric to fit as well as possible into them.

The end result is a perfect fit for my sax with absolutely no movement when it is inside the case, plus a custom look for the interior. Here is a photo:

SaxCase620

Swabbing out a bari sax

And they said it couldn’t be done!

Homemade Leak Light

For occasional home use, it’s handy for a sax player to be able to check for pad leaks. Here’s one I built for just a few dollars, it’s long enough to check my bari and skinny enough I don’t have to remove any pads to use it.

Leak Light

I started with a coat-hanger, straightened it out and bent a small crook at one end.
I wrapped it with two-strand wire. The gauge is not too important. Both voltage and current are low.

At the unbent end, I soldered a battery adapter. 9-volt is convenient because you can just clip it on to turn it on.

At the bent end, I glued a grain of wheat bulb. I used a 12 volt lamp with wire leads. Using it with a 9-volt battery will help it last forever.

Leak Light Bulb

The main down-side is you have to use it in a dark room. Works for me!

Official Facebook plugin for WordPress – SSL Error Solved

This took a day to get working, mainly because of a badly worded Facebook error message. After installing the Facebook plugin on a site, an error message appeared at the top of every Dashboard page:
“SSL must be enabled on your server for Facebook Social Publisher to work.” Seems clear enough doesn’t it?

This WP installation was on a virtual host server, so I studied up on configuring SNI using mod_ssl, created the virtual host section in the Apache config file, bought an SSL cert, installed it, debugged permissions to get the whole thing working. 1 day gone.

Except that didn’t fix the error message! It was still there on each dashboard page. Googling revealed no useful information. So I headed over to the Facebook Developer site to file a bug report. Their bug report form had a bug in it: it would insist you had to enter information in the Tag field, even though I already had done so.

I finally got the answer on the WordPress support forums. It’s nothing to do with SNI or SSL or any of the above. You have to install the curl program to work with PHP on the server. I did so and the error message went away. Talk about a misleading error message… Thanks for wasting my time, Facebook!

New Music Concert Series

Early-onset dementia? Hereditary insanity? Whatever the cause, I am hosting a new music series starting this September. The Ivanhoe Artists of Paterson are allowing me to use the Ivanhoe Wheelhouse, a 19th century mill building with excellent acoustics. All concerts take place on the 3rd Sunday of the month at 1pm.

The focus for this series is a cross-genre survey of experimental music, including free jazz, new classical, electronic and ambient styles. Most of the musicians will be from New Jersey, but I’ll also be showcasing some artists from New York and Pennsylvania.

If this sounds suitably quixotic, please give the Facebook page a Like, or go to the web site and subscribe and you’ll get concert announcements as they happen. Thanks!

Facebook: musiXplore FB

Web: musiXplore main site

M-Audio NRV-10 – machine gun sound, bad caps

I’ve had my M-Audio NRV-10 Firewire interface for over 4 years. It’s a combination mixer and audio interface, which I find quit handy. Last time I went to plug it in, I heard a loud repeating percussive static coming from the monitors. My first thought was that the AC-DC adaptor was bad. It’s 12VDC 3500mA, not a size you can get at Radio Shack, but I had another with a larger amperage. Plugged it in, similar sound.

After digging around on-line, I discovered this is becoming close to a common problem for NRV-10s. For some period of time, they used bad electrolytic capacitors (see Capacitor Plague). These capacitors die within a few years of manufacture. After M-Audio discovered the problem, they extended the warranty to 3 years, but my machine went down after that. I suspect that in a few years there will be very few functioning NRV-10s from before 2008.

There is a helpful video on Youtube that details how to open the unit to check the internal power supply board. The photo shows what my bad board looks like:

NRV-10 power supply with leaking and bulging capacitors

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 out of 9 caps are leaking black goo and/or have bulging tops. Only the one in the upper right corner is still OK.

M-Audio is owned by Avid now. Avid charges for ALL tech support contacts. They want $14.95 for me to tell them I have one of their defective products. As an alternative strategy, I registered on their forum, found the thread for the bad capacitor problem and found the recommended information below:

We are currently out of stock on these capacitors, but in case you or anyone else needs the info, here is the information you’ll need to replace the capacitors on the NRV10 power board:
Remove the 8 capacitors located at C5, C6, C9, C10, C12, C13, C15 and C16 and replace with PANASONIC- EEU-FM1E681 (Capacitor, Electrolytic, 25V, 680uF, Low ESR, 20%, 10x20x5mm)
Remove the capacitor located at C8 and replace with PANASONIC – EEU-FC1J181S (Capacitor, Electrolytic, 63V, 180uF, Low ESR, 20%, 12.5x15x5mm)

I decided to substitute the Panasonics with Nichicon caps. Nichicon has a good reputation. I also increased the voltage rating on the ones I got to give them more robust power handling and longevity. Nichicon UHE2A181MHD (35V) for the 8 caps C5 – C16 and Nichicon UHV1V681MPD (100V) for C8. These cost $1 each at Mouser (mouser.com) instead of $0.67 each for the Panasonics. They are slightly taller, but there is loads of room in the NRV-10 case.

Mirror of VL1 patch site added

Ken Berry has been maintaining a page of patches for the VL1/VL1m since 1995. He has very graciously allowed me to mirror this part of his site, ensuring better availablity of these patches to VL1 users. VL1 Patch Mirror

Tedesco Studios

My band ArtCrime recorded a new album for the Unseen Rain label this week and the sessions were at Tedesco Studios in Paramus. Tom Tedesco has been running this homey place for 20 years. I recommend it for several reasons.

He has a really nice selection of choice instruments. A very good Steinway, a Hammond B3 and a funky old Wurly E.P., among others. His gear is very good: a classic 1940s Neumann condenser, a beautiful Neve console, individual headphone mixes for each performer. The location is ideal for anyone coming from Manhattan or New Jersey.

But the best, I saved for last. He has a 20th anniversary special on: $250 for an entire day. You can record for a week and it will cost the same as 1 day at a studio in the city. Tom is knowledgeable, laid-back and a pleasure to deal with.

Tedesco Studios

MOTU Timepiece – Great Value

Here’s one I stumbled on: the MOTU Timepiece II. The current model is the Timepiece AV, which comes with a USB interface. The Timepiece and Timepiece II have an old style Mac OS9 serial interface, one that Apple dropped in 1999. Sounds like a boat anchor? That’s what most people think, and that’s why it’s such a great value. I picked one up on eBay for $25.
The MOTU Timepiece II MIDI interface
The Timepiece is a very well-made 8-channel MIDI interface, and it’s almost completely programmable from the front panel. No computer needed, so the interface doesn’t really matter. The Timepiece isn’t just an interface, it’s a MIDI patchbay. This means you can route any input by cable or by channel to any output. One setup I use merges inputs 2, 3 and 4 to output 1, so I can use my windsynth plus footpedals to control a rack module. Another setup splits the wind synth output to two channels so I can control Logic Sculpture and a rack synth simultaneously.

The usual issue with the Timepiece is that the original owner has lost the manual. Not a problem! Download the Timepiece AV manual from the MOTU web site. I have been assured by MOTU tech support that the MIDI section applies to the Timepiece and Timepiece II as well as the AV model. Everything I’ve tried from the manual has worked.

The only caveat I have is that the interface is kind of wacky. There are four front panel knobs that control different levels of parameter windows. Once you get used to this, you have a very inexpensive and capable MIDI tool for your studio.

Modifying Sculpture patches for Wind Synths

One of the most powerful Logic softsynths is Sculpture. Most Sculpture patches have been created using keyboards, but it is fairly simple to modify many patches into wind-synth patches.

1. The first order of business is to choose the patch to convert. Patches that are percussive or plucked are not going to work really well on any wind synth. If you modify them enough to work, the character of the final patch will be quite different than what you started with. Here is the part of Sculpture where you choose the object type:

Choosing an Object Type in Sculpture

The object types are circled in red. For best wind-synth compatibility, set these to Blow, Bow, Bow Wide, Noise or Impulse. All of these work better with a gradual note onset. This patch only has Object 1 activated, so we only have to worry about that. Other patches may have more active objects.

2. Next, get rid of any velocity-sensitive characteristics. Wind synths just don’t do velocity and the velocity options will prevent full control of the sound with breath. Here are the parts of the Sculpture interface that are velocity-related:

Velocity Sensitivity in Sculpture

The simplest approach is to turn these all down to 0. However, this will also change the character of the sound, so you might want to map the velocity characteristics to another controller. I use a MIDI Solutions Event Processor to do this when required, but you can get creative with some other controllers on your wind synths or a foot pedal. For this patch, there are no active velocity characteristics, so no worries.

3. Next we set the MIDI controllers at the bottom of the Sculpture screen:

Sculpture MIDI Controllers

At the far right, change the default Mode to “Load from Setting”. The other settings reflect my preferred controller setup: in addition to the controllers on the wind synth, I use 2 foot pedals. One is on 4, the standard foot pedal number. The other is on 30 and controls only the vibrato. At the very least, you will want to set Ctrl A to “2 Breath”.

4. If the patch had an envelope programmed in, you probably want to disable it. You usually build the envelope with the breath controller, so if Env is highlighted(lit up in blue), click on it to deselect it.

Envelope Selector

5. Now you’re ready to actually build the control link to the wind synth. You can do this in two different panels. Each will have a slightly different effect, see which you prefer. First, activate the link by clicking on the big 1 beside it:

Sculpture Controllers 1

6. Next, click and hold under “Target” and select “Object1 Strength” from the dropdown menu:

Sculpture Controllers

7. Finally, if you’re using the Controller A panel at left, slide the button all the way to the right. If you’re using the Controller area at right, set Via to Ctrl A and move both sliders to the right:

Sculpture Controllers

8. Finally, Save As under a different name:

Save As

Other tweaks:

– if the patch has 2 or 3 objects, you will have to repeat the above steps for the other objects. You have to get creative if there are 3 objects, because the Controller A link only has 2 slots. For these, I use Envelope 1 on the right side of the screen for Objects 1 and 2 and Envelope 2 for Object 3.

– most wind synths are duophonic at most, so do your CPU a favor and set Voices to 2.

– you may have to reduce the attach and release times to make the sound work better with a wind synth:

ADSR Change

This just scratches the surface of revising Sculpture patches for wind synth. This is a deep subject, now go practice!

June 13 2017 edit – I’ve added a downloadable collection of Sculpture presets that have been modified to work with wind controllers. There’s a link on the Downloads page, or just click here: Sculpture Presets for Wind Controllers

Unzip on a Mac, then copy to Users/YourUserName/Library/Application Support/Logic/Plug-in Settings/Sculpture. I recommend making a subfolder with a name like Wind, to make them easier to find in Sculpture. To make the user Library folder visible, hold down the Alt key while clicking on the macOS Go menu and choosing Library.